mini2440 board에서 Qtopia booting 하는데까지 나오는 로그데이터입니다.
부팅은 NFS로 하였습니다.
NFS 하드 설정은 Supervivi에서 하여고 부팅합니다.
+---------------------------------------------+
| S3C2440A USB Downloader ver R0.03 2004 Jan |
+---------------------------------------------+
USB: IN_ENDPOINT:1 OUT_ENDPOINT:3
FORMAT: <ADDR(DATA):4>+<SIZE(n+10):4>+<DATA:n>+<CS:2>
NOTE: Power off/on or press the reset button for 1 sec
in order to get a valid USB device address.
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung K9D1208V0M)
Could not found stored vivi parameters. Use default vivi parameters.
Press Return to start the LINUX/Wince now, any other key for vivi
type "help" for help.
Supervivi>
Supervivi>
Supervivi>
Supervivi> param set linux_cmd_line "console=ttySAC0 root=/dev/nfs nfsroot=192.1
68.11.105:/opt/FriendlyARM/mini2440/root_nfs ip=192.168.11.190:192.168.11.105:19
2.168.11.1:255.255.255.0:ubuntu:eth0:off"\
Change linux command line to "console=ttySAC0 root=/dev/nfs nfsroot=192.168.11.1
05:/opt/FriendlyARM/mini2440/root_nfs ip=192.168.11.190:192.168.11.105:192.168.1
1.1:255.255.255.0:ubuntu:eth0:off"
Supervivi> boot
Copy linux kernel from 0x00050000 to 0x30008000, size = 0x00200000 ... done
Warning: this binary is not compressed linux kernel image
zImage magic = 0xffffffff
Setup linux parameters at 0x30000100
linux command line is: "console=ttySAC0 root=/dev/nfs nfsroot=192.168.11.105:/op
t/FriendlyARM/mini2440/root_nfs ip=192.168.11.190:192.168.11.105:192.168.11.1:25
5.255.255.0:ubuntu:eth0:off"
MACH_TYPE = 782
NOW, Booting Linux......
Uncompressing Linux.............................................................
........................................... done, booting the kernel.
Linux version 2.6.13 (root@capcross) (gcc version 3.4.1) #1 Thu Nov 27 09:49:37
CST 2008
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
Machine: QQ2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
BUG: mapping for 0x19000000 at 0xd0000000 overlaps vmalloc space
S3C2440: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: console=ttySAC0 root=/dev/nfs nfsroot=192.168.11.105:/opt/F
riendlyARM/mini2440/root_nfs ip=192.168.11.190:192.168.11.105:192.168.11.1:255.2
55.255.0:ubuntu:eth0:off
irq: clearing subpending status 00000007
irq: clearing subpending status 00000002
PID hash table entries: 512 (order: 9, 8192 bytes)
timer tcon=00000000, tcnt a4ca, tcfg 00000200,00000000, usec 00001e57
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 61056KB available (2515K code, 1032K data, 144K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
USB Power Control, (c) 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C2440: Clock Support, UPLL 48.000 MHz
SCSI subsystem initialized
usbcore: registered new driver hub
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
yaffs Nov 27 2008 09:47:56 Installing.
Initializing Cryptographic API
Console: switching to colour frame buffer device 30x20
S3C24X0 fb0: s3c2410fb frame buffer device initialize done
GPIO L3 bus interface for S3C2440, installed
S3C2410 RTC, (c) 2004 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
leds initialized
buttons initialized
qq2440_pwm initialized
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
DM9000 ethernet driver V1.26 I/O: c481a300, VID: 90000a46
Linux video capture interface: v1.00
ovcamchip: v2.27 for Linux 2.6 : OV camera chip I2C driver
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand: mapped registers at c4880000
s3c2440-nand: timing: Tacls 9ns, Twrph0 39ns, Twrph1 9ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit
)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Bad eraseblock 905 at 0x00e24000
Bad eraseblock 3986 at 0x03e48000
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00030000 : "bootloader"
0x00050000-0x00250000 : "kernel"
0x00250000-0x03ffc000 : "root"
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
usbcore: registered new driver ov511
drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
usbcore: registered new driver gspca
drivers/usb/media/gspca/gspca_core.c: gspca driver 00.60.00 registered
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
s3c2410 TouchScreen successfully loaded
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
s3c2410-sdi s3c2410-sdi: powered down.
s3c2410-sdi s3c2410-sdi: initialisation done.
SBC2440 SOUND driver register
s3c2410-sdi s3c2410-sdi: running at 0kHz (requested: 0kHz).
SBC2440 SOUND driver probe!
SBC2440 UDA1341 audio driver initialized
NET: Registered protocol family 2
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
mmc0: error requesting CID: -110
s3c2410-sdi s3c2410-sdi: running at 198kHz (requested: 197kHz).
s3c2410-sdi s3c2410-sdi: running at 16875kHz (requested: 20000kHz).
nkey register add card device
s3c2410-sdi s3c2410-sdi: running at 16875kHz (requested: 20000kHz).
mmcblk0: mmc0:0001 SDM064 62720KiB
/dev/mmc/blk0: unknown partition table
enable_irq(51) unbalanced from c0170b30
IP-Config: Complete:
device=eth0, addr=192.168.11.190, mask=255.255.255.0, gw=192.168.11.1,
host=ubuntu, domain=, nis-domain=(none),
bootserver=192.168.11.105, rootserver=192.168.11.105, rootpath=
Looking up port of RPC 100003/2 on 192.168.11.105
Looking up port of RPC 100005/1 on 192.168.11.105
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing init memory: 144K
mini2440_backlight: module license 'unspecified' taints kernel.
backlight initialized
[17/Sep/2008:16:32:02 +0000] boa: server version Boa/0.94.13
[17/Sep/2008:16:32:02 +0000] boa: server built Feb 28 2004 at 21:47:23.
[17/Sep/2008:16:32:02 +0000] boa: starting server pid=274, port 80
Please press Enter to activate this console. Create pluginlibman in libqpe
Use QPEApplication's PluginLibraryManager
QMemoryFile::QMemoryFile("/opt/qtopia/etc/dict/dawg")
Created QMemoryfile for /opt/qtopia/etc/dict/dawg with a size of 189396
inserting Documents at -1
could not register server
found obex lib
inserting Applications at 0
inserting Games at 1
inserting Settings at 2
QGDict::hashKeyString: Invalid null key
addAppLnk: No view for type (null). Can't add app (null)!
Create pluginlibman in libqpe
Use QPEApplication's PluginLibraryManager
QuickLauncher running
Registered QPE/QuickLauncher-311
[root@FriendlyARM /]#
